How to use a typewriter: paper, ribbon and return
How to use a typewriter step by step: load paper, set margins, return at the bell, fix mistakes and change the ribbon, on a manual or an electric machine.
To use a typewriter, roll a sheet of paper around the roller, set the margins, and strike the keys firmly one at a time, pushing the return lever at the end of each line when the bell rings. The rest is a handful of small habits: straightening the paper, correcting mistakes and changing the ribbon when the type turns faint.
Machines differ in where their levers sit. If you have the model's instruction manual, follow it where it disagrees with this guide. The names of the parts used here are explained in how a typewriter works.
How to use a typewriter, step by step
1. Load the paper
- Lift the paper bail, the hinged bar with small rollers that lies along the roller.
- Drop a sheet behind the platen, the rubber roller, with its left edge against the paper guide if the machine has one.
- Turn the platen knob until the top of the sheet comes up in front.
- If the sheet is crooked, pull the paper release lever, line the top edge of the paper up with the edge behind it, and push the lever back.
- Lower the paper bail onto the sheet and roll the paper to where you want the first line.
Do not type without paper in the machine, least of all with a fresh ribbon: the type would strike the bare platen.
2. Set the margins
Two sliding margin stops, usually on a rail at the back or front of the carriage, set where each line starts and ends. Move the left stop to where the line should begin and the right stop to where it should end. A scale along the carriage counts character positions.
For a letter, an inch of margin on each side is the usual choice. On a pica machine, which types 10 characters to the inch, that is 10 spaces. The arithmetic for other paper sizes is in pica vs elite.
Set the line spacing too. The line space selector switches between single and double spacing. Single spacing is six lines to the inch.
3. Type
Strike each key with a quick, firm tap and let go at once. On a manual machine your finger supplies the force, so an even rhythm gives even printing, and a soft press gives a faint letter. Press one key at a time: two keys together send two typebars to the same spot, and they jam. Pull them apart gently if that happens.
Hold Shift for a capital. For a run of capitals, press the shift lock, and press Shift to release it. Many older keyboards have no 1 or exclamation mark, for reasons given in typewriter keyboard layout: use a lowercase l for the figure one.
4. Listen for the bell and return
A few characters before the right margin, a bell rings. Finish the word, or break it with a hyphen, then push the return lever at the left end of the carriage all the way across with your left hand. The first part of the push turns the paper up a line and the rest slides the carriage back to the left margin.
If you type on past the bell, the keys lock at the margin stop. The margin release key lets you add the last letter or two.
5. Finish the page
Stop about an inch from the bottom of the sheet. Pull the paper release and lift the page out, or roll it out with the knob.
You can try all five motions before touching a real machine on the online typewriter, which steps the carriage, rings the bell near the margin and returns on the lever or the Enter key.
Correcting mistakes
A typewriter has no delete. Backspace moves the carriage back one space and leaves the ink where it is. Typists used several fixes.
| Method | How it works | Good for |
|---|---|---|
| Typewriter eraser | A hard rubber eraser rubs the ink off the paper | Heavy paper. It can rub through thin sheets |
| Correction fluid | Paint the error out, let it dry, type over it | Any machine. In use since the 1950s |
| Correction tape | Cover the error with the white tape, then type over it | A quick fix of a letter or two |
| X-ing out | Backspace over the word and type x on each letter | Drafts |
| Correction key | On later electric machines, lifts or covers the letter with a built-in tape | Machines that have it. One was announced in 1973 |
Typing the same line again after taking the paper out rarely works, because the sheet is hard to put back in exactly the same place. Correct a mistake while the page is still in the machine. For how much correction a personal letter needs, see how to write a typewritten letter.
How to change a typewriter ribbon
Change the ribbon when the type stays faint however firmly you strike.
Know your ribbon
- Fabric ribbon. Inked cloth on two spools. It winds from one spool to the other as you type, then reverses and is used again, many times over. The de facto standard width is half an inch, about 13 mm.
- Two-color ribbon. A fabric ribbon that is black along one half and red along the other. A color lever chooses which half the type hits.
- Carbon film ribbon. A thin plastic tape, usually in a cartridge, used on many electric machines. The ink transfers completely, so it is used once.
The ribbon width is standard but spools are not. If the new ribbon's spools do not fit, keep your old spools and wind the new ribbon onto them.
Change a spool ribbon
- Before you remove anything, look at how the old ribbon runs: which way it leaves each spool and how it passes through the guide at the printing point. Take a photo.
- Open or lift the cover over the spools.
- Unthread the ribbon from any guides beside each spool and from the ribbon guide in the middle, then lift both spools straight up. The ink will mark your fingers.
- Drop the new spools onto the posts, with the ribbon leaving each spool the way the old one did. On a two-color ribbon, the black half goes on top and the red half below.
- Pass the ribbon behind the middle guide and thread it into its slots. Thread it through the guides beside each spool, if there are any. Check that it lies flat with no twist.
- Put paper in and type a line. The ribbon should travel from the fuller spool toward the emptier one. If it runs the wrong way, flip the ribbon reverse.
Change a cartridge ribbon
Cartridges are made for particular machines, so buy by model and follow the machine's manual. In outline: lift the cover, take out the old cartridge, and fit the new one so that the tape runs in front of the printing point.
Manual typewriter or electric typewriter
| Manual typewriter | Electric typewriter | |
|---|---|---|
| Power | None. Your fingers do the work | Mains electricity and a motor |
| Touch | A firm strike. Darkness depends on force | A light touch. Every letter prints with the same force |
| Return | A lever you push by hand | A return key |
| Ribbon | Fabric on spools | Fabric, or carbon film in a cartridge |
An electric typewriter was produced as early as 1902, without commercial success. The first to enjoy lasting success reached the market in 1929, and a redesigned office model followed in 1935. In 1961 a new design replaced the typebars with a single ball-shaped type element. The first electronic typewriter with a daisy wheel went on sale in 1976.
For a beginner the difference is mostly touch. A manual teaches an even, deliberate stroke and works anywhere. An electric is easier on the hands and prints more evenly, but needs power and, usually, a ribbon made for it.
If you are deciding whether you would enjoy typing this way, spend ten minutes on the online typewriter first, then check your speed and accuracy with the typing test.
Sources
Questions people ask
- How do you use a typewriter?
- Roll a sheet of paper around the platen, set the left and right margin stops, and type with firm, even strokes. When the bell rings, finish the word and push the return lever to start a new line. At the bottom of the page, roll the sheet out and load another.
- How do you change a typewriter ribbon?
- Open the cover, unthread the old ribbon from the guide at the printing point and lift out both spools. Drop in the new spools, thread the ribbon through the guide in the same path, and check that it travels from the fuller spool to the emptier one as you type. On a two-color ribbon the black half goes on top.
- What size is a typewriter ribbon?
- The de facto standard width is half an inch, about 13 mm. The spools differ between machines, so many typists keep the original spools and wind a new ribbon onto them.
- What is the difference between a manual and an electric typewriter?
- On a manual typewriter your finger supplies all the force, so the darkness of each letter depends on how hard you strike. An electric typewriter uses a motor to throw the type, so every letter prints with the same force from a light touch, and a key returns the carriage.
- How do you fix a mistake on a typewriter?
- Cover the error with correction fluid or correction tape and type over it, rub it out with a typewriter eraser, or backspace and type x over the word. Later electric machines had a correction key that lifted the ink off the page.
- Can I practice before buying a typewriter?
- Yes. An online typewriter imitates the motions: the carriage steps with each key, the bell rings near the right margin and the return starts a new line.