Skip to content

Pica vs elite: typewriter type sizes explained

Pica type prints 10 characters per inch and elite prints 12. See how each maps to Courier point sizes and how much fits on a Letter or A4 page.

8 min read

Pica and elite are the two standard typewriter type sizes. Pica prints 10 characters to the horizontal inch and elite prints 12. Both normally print six lines to the vertical inch, so the difference is all in the width: on the same paper, an elite line holds 20 percent more than a pica line. In word processor terms, pica is 12 point Courier and elite is 10 point Courier.

Pitch means characters per inch

On a standard typewriter the carriage moves the same distance for every keystroke, whether you strike an i or an m. Because every character gets the same width, typewriter type is sized by pitch: the number of characters in one inch of a typed line.

Ten pitch is pica. Twelve pitch is elite. A pica character sits in a cell one tenth of an inch wide, which is 2.54 mm. An elite character sits in a cell one twelfth of an inch wide, about 2.12 mm.

Neither word names a design. Each maker cut its own faces, and collectors who have looked into it agree there is no single pica or elite letterform, only the shared spacing.

Line spacing is a separate mechanism. The ratchet on the platen sets it, not the type, and on most machines a single spaced line feeds the paper one sixth of an inch. Some machines were built to feed 5 1/3 lines to the inch instead. A patent filed in 1976 for a platen that switches between the two calls them the most common rates. Six is the standard figure, and the one every page format below assumes.

Pica and elite at a glance

Measure Pica Elite
Pitch, characters per inch 10 12
Width of one character 1/10 in, 7.2 pt, 2.54 mm 1/12 in, 6 pt, 2.12 mm
Lines per inch, single spaced 6 6
Matching Courier size 12 point 10 point
Line on US Letter, 1 in margins 65 characters 78 characters
Line on A4, 1 in margins 62 characters 75 characters
Lines per page, Letter and A4 54 and 58 54 and 58
Full page of characters, Letter and A4 3,510 and 3,596 4,212 and 4,350

You can compare the two on the Typebar typewriter, which has a pica face and an elite face, plus a letter spacing control for a pitch between or outside them.

Why 12 point Courier is 10 pitch and 10 point is 12 pitch

Point size measures the height of type, at 72 points to the inch. Pitch counts widths. The two are tied together only by the proportions of a particular font.

Courier was drawn by Howard Kettler in the mid 1950s as a typewriter face, and its digital versions keep one proportion throughout: every character is six tenths as wide as the point size.

  • At 12 points, each character is 12 × 0.6 = 7.2 points wide, and 72 ÷ 7.2 = 10 characters per inch. That is pica.
  • At 10 points, each character is 10 × 0.6 = 6 points wide, and 72 ÷ 6 = 12 characters per inch. That is elite.

The numbers appear to trade places because one measures size and the other counts how many fit. Larger type, fewer to the inch.

Two cautions apply when you match a typewriter in a word processor.

The six tenths rule belongs to Courier and to fonts built to its width, Courier New among them. Other monospaced fonts do not all share it, so check by typing ten characters and measuring them.

Single spacing is not six lines to the inch. Courier New carries a built-in line height of about 13.6 points at the 12 point size, which works out to roughly 5.3 lines per inch. Set the line spacing to exactly 12 points if you want the typewriter's six.

For the letterforms themselves, see which fonts look like a typewriter.

How much fits on US Letter and A4 with one inch margins

US Letter is 8.5 by 11 inches. One inch margins on every side leave a block 6.5 inches wide and 9 inches tall.

  • Pica: 6.5 × 10 = 65 characters per line.
  • Elite: 6.5 × 12 = 78 characters per line.
  • Either size: 9 × 6 = 54 lines single spaced, or 27 double spaced.

A4 is 210 by 297 mm, or 8.27 by 11.69 inches. The same margins leave 6.27 by 9.69 inches.

  • Pica: 6.27 × 10 = 62.7, so 62 whole characters per line.
  • Elite: 6.27 × 12 = 75.2, so 75 characters per line.
  • Either size: 9.69 × 6 = 58.1, so 58 lines single spaced, or 29 double spaced.

A4 is narrower and taller than Letter, so each line loses three characters and each page gains four lines.

Filled from margin to margin, a Letter page holds 65 × 54 = 3,510 pica characters or 78 × 54 = 4,212 elite characters. On A4 the totals are 62 × 58 = 3,596 and 75 × 58 = 4,350. A real page holds fewer, because lines end at word breaks and paragraphs leave gaps.

Ignore the margins and the full 8.5 inch width of a Letter sheet is 85 pica spaces or 102 elite spaces. Halve those and you have the center of the page, which is how typists placed a heading.

Why an office chose pica or elite

We found no reliable count of how many machines were sold in each size, and collectors' estimates of which was more common disagree. The reasons people give for choosing one are more consistent.

Elite was the economical size. Twenty percent more characters on a line kept a long letter to one sheet under a printed letterhead, and it let a typist fit entries into the small boxes on printed forms. People with office experience on one collectors' forum thread remember single spaced elite as the ordinary business letter for those reasons.

Pica was the legible size. The letters are larger, and the same thread notes that it was picked for pages that would be copied, where clarity mattered. It was also the size expected in double spaced court filings, manuscripts and scripts, which is why it survives in the formats described below.

Habit counted too. Another poster there recalls large firms continuing to order pica so that all their letters matched.

Other pitches: 11, 15 and proportional

Pica and elite were the standards, not the only choices.

Eleven pitch and micro

Many European portables type 11 characters to the inch, and sellers often still describe them as elite. The elite label on a European machine is not always 12 pitch.

Micro is smaller again. Electronic typewriters often had a pitch selector marked 10, 12 and 15 for pica, elite and micro.

Proportional spacing

Proportional spacing leaves the system altogether. An electric office typewriter with proportional spacing went on sale in 1944. Its characters took between two and five units of width each, so an i used less room than an m and the page looked closer to print. A proportional face has no pitch, because the number of characters in an inch depends on which characters they are.

Dot matrix printers later carried the old names into computing, with pica and elite modes at 10 and 12 characters per inch and condensed modes at 17 or more.

What pica means in printing, and how the two meanings connect

A printer's pica is a unit of length equal to 12 points. In desktop publishing a point is exactly 1/72 of an inch, so a pica is exactly one sixth of an inch. The older American printer's pica, fixed by the type founders in 1886, is 0.16604 inch, a shade under one sixth.

Before type sizes were given in points they had names, and pica was the name for 12 point type.

The two meanings meet in the line. A pica typewriter prints six lines to the inch, so each line is 12 points deep, which is one printer's pica. On that measure its type is 12 point, the size printers called pica, and the 10 characters per inch follow from giving every letter the same width at that size.

Who first applied the printer's word to a typewriter is not recorded in any source we could find, so treat the borrowing as the usual explanation, not a documented event. Elite does not appear among the traditional size names, where 10 point type was called long primer, so it looks like a typewriter coinage.

Manuscript and screenplay formats descend from pica

Two professional page formats are pica pages that outlived the machine.

Standard manuscript format asks for Courier or a similar monospaced font at 12 points, double spaced, with margins of 1 to 1.5 inches and about 25 lines to a page. The point of the uniformity is counting. With 1.25 inch margins a Letter line is 6 inches, or 60 pica characters. Editors reckon six characters to a word, spaces included, so a line is 10 words and a 25 line page is 250 words. The familiar figure of 250 words per manuscript page is pica arithmetic.

Screenplays kept the pitch in the rule itself. The Academy's guidance for its Nicholl Fellowships lists as a fault any font other than "Courier 12-point, ten-pitch, non-proportional". The rule of thumb that one script page runs about a minute on screen is loose at best, and it would mean nothing if writers' pages held different amounts.

How to tell whether a machine is pica or elite

  1. Find the numbered scale on the paper bail or the carriage.
  2. Lay a ruler along it and count the divisions in one inch.
  3. Ten divisions means pica and twelve means elite. Eleven means an 11 pitch face, common on European portables.

With only a typed page to go on, measure one inch along any line and count the characters, spaces included.

To see what the choice does to a page, type the same paragraph twice on Typebar, once in each face, and count where the lines break.

Questions people ask

What is the difference between pica and elite type?
Pica type prints 10 characters to the horizontal inch and elite prints 12. Both normally print six lines to the vertical inch, so an elite line holds 20 percent more than a pica line on the same paper.
Is 12 point Courier pica or elite?
12 point Courier is pica. Every Courier character is six tenths of the point size wide, so at 12 points it is 7.2 points wide and ten fit in an inch. Courier at 10 points fits twelve to the inch, which is elite.
How many characters fit on a typewritten line?
With one inch margins, US Letter paper takes 65 pica or 78 elite characters per line, and A4 takes 62 pica or 75 elite. Either size fits 54 single spaced lines on Letter and 58 on A4.
Is a typewriter pica the same as a printer's pica?
No. A printer's pica is a unit of length equal to 12 points, about one sixth of an inch, while typewriter pica is a type size of 10 characters per inch. They meet in the line spacing: a single spaced typewriter line is 12 points deep, which is one printer's pica.
How can I tell whether a typewriter is pica or elite?
Count the divisions in one inch of the scale on the paper bail or carriage. Ten means pica and twelve means elite. On a typed page, measure one inch of a line and count the characters, spaces included.